If you had the guts for M-19's

[Cal Weldon]

with proper 288's and 1505's on top.

I have the 288 8 ohm aluminum version redone at GPA but I would have to settle for 1803 horns.

The 360 Onken was what the 'C' owner wanted, so we built it, but I was underwhelmed overall.

Thank you for posting it over at the other site but this is not good news.

Apologies folks! My previous post reads with a bit of a "snarky" tone, wasn't my intent to impart the tone, just the opinion.

Ya, none of us have EVER done anything like that you *******!

[Cal Weldon]

Forgot to mention, my babies came home from the hospital today. All nice and shiny. New dust caps, new goop, don't they look beautiful? Sorry for the poor pic.

[voice of the theater]

Forgot to mention, my babies came home from the hospital today. All nice and shiny. New dust caps, new goop, don't they look beautiful? Sorry for the poor pic.

Where did you send them--GPA? They look great! (lightened up your photo with photoshop)

[Cal Weldon]

Wow, under that light they look horrible! Where's all that crap coming from on the surrounds? How come the cones aren't black?

Thanks VOTT. They were done here in town at Vancouver Audio Speaker Clinic. The cones remained original. I asked them to pull the dust caps, clean the gaps the best they could [yes, I know], realign one of the coils, clean the surrounds and add some new goop. Once home I gave them some TLC to tidy them up a bit.

[voice of the theater]

Wow, under that light they look horrible! Where's all that crap coming from on the surrounds? How come the cones aren't black?

Thanks VOTT. They were done here in town at Vancouver Audio Speaker Clinic. The cones remained original. I asked them to pull the dust caps, clean the gaps the best they could [yes, I know], realign one of the coils, clean the surrounds and add some new goop. Once home I gave them some TLC to tidy them up a bit.

Glad to hear you were able to keep the original cones--looks like they did some nice work on the "spruce up". The only place I would trust for a full re-cone for my vintage Altecs (if they ever need it) is GPA. BTW, maybe I lightened your photo too much! Is this better?

[bowtie427ss]

The only place I would trust for a full re-cone for my vintage Altecs (if they ever need it) is GPA.

I know a couple fellas "in the business" in that corner of the world, Vancouver Audio is a long and well trusted speaker repair center. They likely source their Altec related parts from GPA, or from the same source GPA does depending on the part, and their work is absolutely on par with GPA's. I've owned some of their work in the past, and if i lived west of the Rockies they'd pretty much be my exclusive speaker repair folks. East of the Rockies GPA is a no-brainer for Altec and Gauss rebuilds, even used to be able to talk them into some Emilar cone repairs a few years back.

[Cal Weldon]

vott: That second pic is spot on. Thanks very much.

bowtie: glad to hear you like them. Even after David Lee passed away a year ago [or so] and they closed shop, the rest of the gang recruited the original owner Tom to start it back up again. They've always been good to me and yes I believe you are right about their quality and them sourcing the right parts.

[valhallax]

i would start by at least doubleing the woofers

[GM]

I have the 288 8 ohm aluminum version redone at GPA but I would have to settle for 1803 horns.


Thank you for posting it over at the other site but this is not good news.

Poor, poor, pitiful you.

You're welcome! what can I say? After 416A, -B, 515B, the early Ferrite had a tough act to follow. The 360 was too large for the high tuning, so all I could do was increase series resistance and stuff ports. It wasn't bad, just not optimal. An Onken alignment would probably be fine if designed with measured specs + any series resistance.

GM